PRO-SEAL^® 34
The World's Most Versatile Sealant

ATTENTION ASTROSEAL USERS!

With PRO-SEAL 34 you can still:
   Seal under water
   Seal through oil
   Use in high & low temperature
       environments 
   Apply to: Teflon, Stainless Steel, Galvanized
       Aluminum, Ferrous or non-ferrous materials

"PRO-SEAL 34 sticks to whatever it touches and seals it.”  

SEALS UP TO 800°F

THE PROBLEM
SOLVER HAS
ARRIVED!

 Seals through: oil, under water, in high temperatures  
Seals on: TFE, Hypalon, Stainless Steel,
Galvanized Aluminum

• SEALS UNDER WATER
  Only co-polymerized PRO-SEAL 34 has M-34 that seals through water. Use it in the rain or under water. It will stop your leak immediately.
  
  

• HIGH TEMPERATURE SEALING
  High to low temperature changes will not break the seal. PRO-SEAL 34 temperature limitations are unique. Service temperature range is -50°F to 220°F. Applications over 800°F may be successful in moist environments, especially as a gasket compound. Test areas are advised if there is any doubt. Do not heat tube over 122°F. When applying be sure surface temperature is between -50°F to 95°F and temperature inside tube is between 50°F to 95°F.
  
  

• SEALS THROUGH OIL
  No need to spend hours cleaning the surface to apply. PRO-SEAL 34 works through oil and water to provide an instant seal.
  
  

• COMPOSITION
  PRO-SEAL 34 is based on a proprietary, high molecular weight, elastomeric copolymer. This specialty resin is modified producing a sealant with exceptional adhesion, elasticity, and resistance to tear, shear, stress, and weathering. PRO-SEAL 34 is non-toxic when fully cured.
  
  

• APPLICATIONS
  Gasket, or gasket repair, fill voids, stop under water line leaks, leaking tanks, piping, etc.
  
  

• SEALS PROBLEM MATERIALS
  TFE, Hypalon, stainless steel, galvanized aluminum, ferrous or non-ferrous materials and any combination of the above.
  
  

• CHEMICAL RESISTANCE
  PRO-SEAL 34 is normally inert to solvents and alkali's. This resistance can be greatly affected by temperature, cure time, and even the presence or lack of moisture during and after the application. Testing is strongly advised or consult the factory.
  
  

• CLEANING
  Remove PRO-SEAL 34 from the gun before it cures. This may be done by using solvents such as Acetone, Xylol, Toluol or chlorinated solvents and scraping. Cured materials may be removed by cutting with a sharp tool. Observe manufacturer's precautions when using toxic or flammable solvents. Do not smoke.
  
  

• LONG SHELF LIFE
  Guaranteed 2 years unopened; 6 months opened. Cover or plug opened portion of nozzle with tape or nail to impede curing. Should material in nozzle cure, remove nozzle and clean it or replace the nozzle.
  
  

• 100% RESEALABLE
  In its cured state, PRO-SEAL 34 will rejoin to itself if the bead is broken. It will also adhere to itself if additional material applied over the cured material.
  
  

• PAINTABLE
  Sealing may be painted immediately; however, for best results, wait 24 hours before painting.
  
  

• STRETCHES AND FLEXES
  PRO-SEAL 34 stretches 350% and stays sealed in high vibration and expansion areas. It stays flexible and will not become brittle.
  
  

• SURFACE PREPARATION
  Priming is generally not required, except for saturated wood and wet cement. Contact EPD Technology for technical assistance.
  
  PRO-SEAL 34 sticks to what it touches first, so free surface of dust, dirt and other contaminants.
  
  Some chemicals or solvents used for cleaning require a waiting period to ensure no residue remains.
  

LIMITATIONS
PRO-SEAL 34 is a sealant, not a cement. If a hole is large and/or pressure is to be sealed, build a dam using PRO-SEAL 34 in conjunction with a strengthening agent such as fiberglass, steel plate, etc.

In food process or storage area, a two week cure is required at room temperature. PRO-SEAL 34 is not FDA approved.

Since PRO-SEAL 34 never totally cures, it is not recommended in areas requiring vigorous cleaning or in high traffic areas.

APPLICABLE STANDARDS
Fed. Spec. TT-S-00230C, Class B, Type 11.

CURE TIME
Usable immediately, 4-5 hrs. initial cure, 48 hrs. normal for solvent release.

PACKAGING
10.2 fl. oz. plastic cartridges with removable screw-on nozzle. Packed 20 to a pack. Pails and drums upon request.

CAUTION
Use in well-ventilated areas and avoid contact with skin or eyes. Do not induce vomiting if swallowed, contact a physician immediately. Keep out of reach of children.

 Click here for a Material Safety Data Sheet

PRO-SEAL 34 - In General

• Tip contact is essential. PRO-SEAL 34 sticks to whatever it first touches.

• Applying light pressure maintains good tip contact and helps fill voids and cracks.

• PRO-SEAL 34 is 100% resealable. Once a joint sealed with PRO-SEAL 34 is broken, just add material upon remaking the joint. It is not necessary to remove old material even if water or oil spill over it or the joint has been closed for long period.

• To finish or tool, use a soap solution for lubricant.

• Use a standard high quality caulking gun.
  

GUARANTEE

The Manufacturer warrants that the product is manufactured according to their published standards and that the product is free from defects.

EPD will, at its' option, either refund the purchase price or provide replacement for that portion of the PRO-SEAL 34 which fails to perform in accordance with this warranty. Such refund or replacement will constitute the limit of EPD Technology liability and obligation for any such failure.

EPD Technology will not be liable or obligated otherwise for any loss or damage, arising directly or indirectly, from PRO-SEAL 34 or the use or failure thereof, whether based on breach of warranty or negligence.

PRO-SEAL 34 PRICES

1 sample tube . . . . . . . . . . . . . . . . $15.95    

1 pack of 20 tubes . . . . . . . . . . . $12.95 each   

1 case of 80 tubes . . . . . . . . . . . . $11.95 each  

products	home	search	feedback

free catalog	shopper service